PRODUCT INTRODUCTION
Spring cone crusher is suitable for crushing various of mid-hard ores and rocks. This crusher has the advantages of reliable construction, high productivity, easy adjustment and less cost in operation. The spring release system of crusher acts an overload protection system that allows tramp to pass through the chamber without damage the crusher, use dry oil, water, two kinds of sealed formation. It made plaster stone and engine oil seprated, assured reliable performance,the type of crushing chamber depends upon the size of feed and fineness of the crushed product. The standard type is applied to medium crushing , the medium type is applied to medium or fine crushing and the short head is applied to fine crushing.
20-30mm、10-20mm、5-10mm、0-5mm
It can crush more than 100 kinds of rocks. The common discharge size is...
Features
Simple structure and strong crushing force
The unit energy consumption is low, the crushing ratio is large, and the crushing effect is good.
Multi-purpose machine, green and environmental protection
The electric cooling system lubricating oil station is adopted, and the lubricating station realizes automatic control.
Safe and reliable operation
16 groups of high-performance alloy steel springs can effectively ensure the safety of the crusher.
Easy maintenance and low maintenance
All parts can be disassembled from the top or side, which is convenient for the disassembly of the fixed cone and moving cone assembly.
WORKING PRINCIPLE
Cone crusher crushes materials by the working surface between the movable cone and fixed cone. So it is more advanced and efficient than jaw crusher. The movable cone is supported by spherical bearing and fixed on an hanging erect shaft which is set in the eccentric sleeve, and the sleeve is set on the stopping and pushing bearing. The movable cone and erect shaft are driven by the eccentric shaft sleeve together. The eccentric shaft sleeve is driven by horizontal shaft and fimbriated gear, and the wheel of the conveyor belt is driven by motor through v-belts. The lower part of vertical shaft is installed in the eccentric sleeve. When the eccentric sleeve rotates, there is a conical surface lined out by the shaft. When the movable cone comes near the fixed cone, rocks are grinded into pieces, when the movable cone leaves, grinded materials is discharged from the discharge hole. The fixed cone can be ascended or descended by adjusting setting to adjust the width of discharge hole, consequently the output size is determined adjusted.
Technical specifications
| Model |
Diameter of crushing cone(mm) |
Feeding size(mm) |
Adjusting Range of Discharge Opening(mm) |
Capacity(t/h) |
Power(KW) |
Eccentric Shaft Rotate Speed(r/min) |
Weight(t) |
Overall Dimension(mm) |
| PYB600 |
Φ600 |
≤ 75 |
12-25 |
15-25 |
30 |
356 |
5 |
2234 x 1370 x 1675 |
| PYD600 |
Φ600 |
≤ 35 |
3-13 |
5-23 |
30 |
356 |
5.3 |
2234 x 1370 x1675 |
| PYB900 |
Φ900 |
≤ 115 |
15-50 |
50-90 |
55 |
333 |
11.2 |
2692 x1640 x2350 |
| PYZ900 |
Φ900 |
≤ 60 |
5-20 |
20-65 |
55 |
333 |
11.2 |
2692 x 1640 x 2350 |
| PYD900 |
Φ900 |
≤ 50 |
3-13 |
15-50 |
55 |
333 |
11.3 |
2692 x 1640 x 2350 |
| PYB1200 |
Φ1200 |
≤ 145 |
20-50 |
110-168 |
110 |
300 |
24.7 |
2790 x 1878 x 2844 |
| PYZ1200 |
Φ1200 |
≤ 100 |
8-25 |
42-135 |
110 |
300 |
25 |
2970 x 1878 x 2844 |
| PYD1200 |
Φ1200 |
≤ 50 |
3-15 |
18-105 |
110 |
300 |
25.3 |
2790 x 1878 x 2844 |
| PYB1750 |
Φ1750 |
≤ 215 |
25-50 |
280-480 |
160 |
245 |
50.3 |
3910 x 2894 x 3809 |
| PYZ1750 |
Φ1750 |
≤ 185 |
10-30 |
115-320 |
160 |
245 |
50.3 |
3910 x 2894 x 3809 |
| PYD1750 |
Φ1750 |
≤ 85 |
5-13 |
75-230 |
160 |
245 |
50.2 |
3910 x 2894 x 3809 |
| PYB2200 |
Φ2200 |
≤ 300 |
30-60 |
490-750 |
260-280 |
220 |
80 |
4622 x 3302 x 4470 |
| PYZ2200 |
Φ2200 |
≤ 230 |
10-30 |
200-580 |
260-280 |
220 |
80 |
4622 x 3302 x4470 |
| PYD2200 |
Φ2200 |
≤ 100 |
5-15 |
120-340 |
260-280 |
220 |
81.4 |
4622 x 3302 x4470 |
